Just figured out how to do a P2P linkup between two nodes on my mesh. I will post info if there is anyone interested in this.

Jerry

I have Asterisk running on a Raspberry Pi with no issues. I tried the install on one of the 54GS. And after a boot it now has no WAN LED. It is not visible from anywhere. Luckily I have three more nodes to use. 

I forgot my admin password. What do I need to do? 

Rick, KI7NDY

I forgot my admin password. What do I need to do? 

Rick, KI7NDY

I forgot my admin password. What do I need to do? 

Rick, KI7NDY

Have two Cisco 7940 IP phones and a Motorola XT801 with a Grandstream HT701. Connected over a 2.4 Broadband-Hamnet mesh network.

Youtube link below.

https://youtu.be/Iyy2Soiv57o

No worries. I got into the router via the wireless connection from the other mesh node and re-enabled DHCP.

Also downloaded and started experimenting with Wireshark and trying to learn a little more about IP addressing.

Kind of disappointed though that I got no replies on the forum. I'm sure many amateurs who are not networking experts are reluctant to get into MMSH-mesh because of the associated technical issues. It is admittedly pretty easy to flash a Linksys router to create a mesh node, but doing something useful with it afterwards requires a lot more networking expertise or mentoring from others who are more knowledgeable.

There are no mesh nodes anywhere near my location that I can connect with so will have to simply experiment with the two that I have set up and figuring at this point that it I will pretty much have to do so on my own.

Rick VE3ORY

I have three Linksys 54GS routers and one Buffalo WHR-HP-G54 working on my Mesh. I have two Cisco 7940 IP phones connected to Astrisk running on a Raspberry PI. 

Hello,

I have a lot of the following routers: https://openwrt.org/toh/zinwell/zw4400

I have successfully installed OpenWRT...but as there is no available version of Broadband-Hamnet, I need to know how to configure the wireless interfaces for mesh.

In addition: I will have 420, 900, 2.4 and 5.4 cards available, so is it possible to bridge the various frequencies into one network that is one mesh?

73,

KB3VWG

(also is it possible to get an x86 and IXP42x-tw5334 target of Broadband-Hamnet, or where can I find the files to compile?)

I have been experimenting with two WRT-54G routers that I successfully set up with HSMM-Mesh .

In my experimenting, I disabled the DHCP server on one of them (WRT-54G v3) and now cannot access that mesh node via the ethernet connection using my web browser. ipconfig says that no IP address has been issued by the connected device. I guess I know why.

So my question becomes: Is there a way to get back into my mesh node so that I can re-enable the DHCP function?

Also...is there a way to reset the router to default HSMM-Mesh settings so that I can get into it and start over?

Sorry I really need some help with this, as I am really a newbie with networking issues.

Thanks, Rick VE3ORY

Hi.  Newbie here.  I'm curious if anyone is in the Charleston (Mt. Pleasant) area and working on a node.  I would like to see if there is anyone to connect with out here before going too far down the rabbit hole.

Michael

KE4DHK

Hi.  Newbie here.  I'm curious if anyone is in the Charleston (Mt. Pleasant) area and working on a node.  I would like to see if there is anyone to connect with out here before going too far down the rabbit hole.

Michael

KE4DHK

Hi.  Newbie here.  I'm curious if anyone is in the Charleston (Mt. Pleasant) area and working on a node.  I would like to see if there is anyone to connect with out here before going too far down the rabbit hole.

Michael

KE4DHK

Hi.  Newbie here.  I'm curious if anyone is in the Charleston (Mt. Pleasant) area and working on a node.  I would like to see if there is anyone to connect with out here before going too far down the rabbit hole.

Michael

KE4DHK

So i have 3 WRT54G devices flashed and running, all seeing each other. The question I have is now I am reading and trying to share the internet from node A at my router to node B in my bedroom for testing in the same house. I did check "mesh gateway" at node A at the router, reset, but still the same result. I did see some forums about port forwarding on node A? but what steps am I missing? I tried for the heck of it forwarding port 80 on node A at the router, of course it did no good.  Any help would be appreciated. Thanks

Feel free to also email me some info at admin@hamradioconcepts.com

I now have two nodes set up, one on Linksys hardware (node 1) and one on Ubiquiti hardware (node 2).  Node 1 displays Node 2 status fine.  Node 2 can see Node 1 but is unable to display Node 1 status.  Both are running freshly downloaded firmware 3.1.0.  Plenty of signal strength since both nodes are in same room.  I also installed HamChat on both nodes and have one-way transmission at best.  Anything I should check or try?

Keith - KE4TH